بال پیچ مشین ٹولز اور صحت سے متعلق مشینری میں سب سے زیادہ استعمال ہونے والے ٹرانسمیشن اجزاء ہیں۔ اس کا بنیادی کام گردشی حرکت کو لکیری حرکت میں تبدیل کرنا، یا ٹارک کو محوری دہرائی جانے والی قوت میں تبدیل کرنا ہے۔ ایک ہی وقت میں، اس میں اعلی صحت سے متعلق، ریورسبلٹی اور اعلی کارکردگی کی خصوصیات بھی ہیں۔
سنکیت: فکسڈ سائیڈ اور سپورٹنگ سائیڈ کے درمیان سینٹر انحراف سے مراد ہے۔
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60m/منٹ، اور جبری تیل کی دھند پھسلن کو 60 سمجھا جا سکتا ہے۔-100m/منٹ یہ ایک کھوکھلی سکرو آرڈر کرنے اور زبردستی کولنگ اور چکنا کرنے کی سفارش کی جاتی ہے۔ کام کرنے والے ماحول کو صاف رکھیں اور دھول اور دیگر نجاست کو ریس وے یا نٹ میں داخل نہ ہونے دیں۔ اگر صورتحال اچھی نہیں ہے تو، پیچ میں حفاظتی کور شامل کرنے پر غور کریں۔
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①اعلی ٹرانسمیشن کی کارکردگی. بال سکرو ٹرانسمیشن کی ترسیل کی کارکردگی عام طور پر 20.92 ہے۔-10 فیصد، اور عام سلائیڈنگ سکرو ٹرانسمیشن کی ٹرانسمیشن کی کارکردگی 20.20 ہے-0.40.
②ٹرانسمیشن کی اعلی درستگی، مستحکم حرکت اور کوئی رینگنے والا رجحان نہیں۔ بال سکرو ڈرائیو بنیادی طور پر رولنگ رگڑ ہے، چھوٹی رگڑ مزاحمت کے ساتھ، اور رگڑ مزاحمت کا حرکت کی رفتار سے تقریباً کوئی تعلق نہیں ہے۔
③بغیر کسی کام کے ریورس گیئر میں دوڑنا۔ گیند کے سکرو اور نٹ کو پہلے سے سخت کرنے کے بعد، محوری کلیئرنس کو ختم کیا جا سکتا ہے۔ اس طرح، مخالف سمت میں کوئی ڈیڈ زون نہیں ہے، اور محوری ٹرانسمیشن کی درستگی اور سختی بہتر ہوتی ہے۔
④یہ الٹنے والا ہے۔ چونکہ بال سکرو کا رگڑ کا نقصان چھوٹا ہے، اس لیے اسے روٹری موشن سے لکیری موشن میں تبدیل کیا جا سکتا ہے، اور اسے لکیری حرکت سے روٹری موشن میں بھی تبدیل کیا جا سکتا ہے۔ لیڈ سکرو اور نٹ دونوں کو ڈرائیو یا پیروکار کے طور پر استعمال کیا جا سکتا ہے۔
⑤طویل سروس کی زندگی. رولنگ رگڑ کے چھوٹے رگڑ نقصان کی وجہ سے، سروس کی زندگی طویل ہے.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
ابھی رابطہ کریں۔
E-mail: sales@gyballscrew.com Tel(واٹس ایپ): جمع 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
